Monitor and Modify Variables in Simatic Manager

In this article, I will show you how to monitor and modify variables from the hardware configuration using the Siemens Simatic manager.

Monitor and Modify Variables

Follow the below steps to monitor and modify variables from the hardware configuration.

Step 1:

Open Simatic manager. Select the “CPU” and double click on “hardware” to enter in to hardware environment.

Step 2:

The following hardware configuration window will open up.

Step 3:

To monitor or modify a variable, select digital input or output card and do right-click to open properties as you can see in the below window.

Click on monitor/modify to open a new window.

To monitor or modify a variable, download project to the simulator.

Step 4:

The following window will open up. Here, as I have selected digital inputs, it will only show digital inputs.

Step 5:

To monitor the input variable, do checkmark as shown in the below window.

Keep the program in monitor mode to see the status of the input variable.

Step 6:

Now to modify the value or to change the status of the input variable, use the modify option.

To modify a value, click on modify value and write “0” or “1” then click on “modify value” to make changes.

Step 7:

Under modify and monitor option, there is one more tab “ trigger” is available.

Clicking on the trigger will open up a new window.

Here, as you can see triggering options for modifying and monitoring value.

You can set it as per your requirement for a single scan cycle or every scan cycle.

Comments

What is a Torbar? – Averaging Pitot Tubes

The Torbar is employed for flow measurement of liquids, gases, or steam in circular, square, or rectangular section ducts for large flow rates. The Torbar is an insertion type multi-port self-averaging primary sensor for flow measurement. Torbar TORBAR is a set of Pitot tubes mounted on a bar across the pipeline with no moving parts. An averaging Pitot tube is a technology, while TORBAR is a manufacturing brand name. There are several brands available in the market with VERABAR, ANNUBAR, etc. Averaging Pitot Tube Principle Purpose Averaging Pitot tube can be employed when the average velocity of the flow profile, rather than the velocity in a specific point in the cross-section is desired. Averaging Pitot Tubes Principle It measures the differential pressure between the static pressure tap and the tap of full pressure of a stream. Thus such magnitude of differential pressure is directly proportional to the square of the flow rate. Working The TORBAR is designed in such a way that ...

Ferrules and Cross Ferruling

Ferrules are identification labels provided for every wire terminations in an instrument, equipment, or electrical/instrumentation control panels. These tube-shaped sleeves can be inserted easily on each individual wire in a multi-core cable. In earlier days fixed digits/letters are used as ferrules, but now Instrumentation engineers/technicians prints out desired ferrules by using a ferrule printing machine. Typical Ferrule The numbers/ letters on the ferrules will be given as per the approved electrical hook up or loop diagrams. This helps technicians to easily identify a particular loop/wiring from a series of terminal blocks and to troubleshoot the desired terminal connection. Separate numbers on the ferrules distinguish the positive and negative polarities of wires, thus ensure the polarity protection of the instrument. Cross Ferruling As a wire is connected on its both ends, it is quite useful to use a cross reference method for wire identification. Unlike normal ferru...

Thermowell Insertion and Immersion Length

The thermowell is the industrial housing for temperature elements like RTD or thermocouple or temperature gauges. Thermowell is directly exposed to process fluid/media. Inside the thermowell, element/gauge is installed. Thermowell transfers the heat to the temperature element. Depending upon the element type, the fluid temperature can be known. So Thermowell protects the temperature element against harsh conditions and process fluid. It enables removal of the temperature element for replacement, repair, or testing without affecting the process system. Generally, thermowells are provided with all-temperature Elements like RTD or Thermocouple or temperature gauge. A few exceptions would be bearing RTD, skin type thermocouple, air duct thermometer, etc where thermowell is not applicable / required. When the thermowell assembly is inserted into the pipe, it is subjected to vibration. This vibration is caused by vortices to be generated alternately on either side of the thermowell. The...

TILI Automation

Search This Blog