Installation and Calibration of Level Transmitter

This article covers the basic steps and brief guidelines for the installation and calibration of level transmitters used in the industries.

Guidelines for Installation of Level Transmitter

1. Install The Transmitter With Proper Support.

2. Use Proper Cable.

3. Keep Corrosive & Hot Process Material away From the Transmitter.

4. Keep Impulse Piping As Short As Possible.

5. Keep Minimum Joints, Bends In Impulse Piping.

6. Keep Liquid Head as always liquid filled up.

7. Avoid Sediment Deposits In The Impulse Piping.

8. Avoid Ambient Temperature Gradient and Fluctuations.

9. Check For Any Leaks in The System.

10. Provide Insulation If Necessary.

Guidelines for Calibration of Level Transmitter

1. Isolate The Transmitter Properly.

2. Drain-All The Legs and Transmitter Properly.

3. Use Valid Calibration / Test Equipment.

4. Check For Any Leakages in The System.

5. Fallow Calibration Procedure Given In Manual.

6. Check The Transmitter Output Repeatability Properly.

7. Please Update The Calibration Records.

8. Please Fill Up The History Card.

9. Take The Transmitter In Line With The Help OF Manifold & Block Valves (for DP Transmitter).

10. Properly Plug All The Drains of Impulse piping.

Comments

Ferrules and Cross Ferruling

Ferrules are identification labels provided for every wire terminations in an instrument, equipment, or electrical/instrumentation control panels. These tube-shaped sleeves can be inserted easily on each individual wire in a multi-core cable. In earlier days fixed digits/letters are used as ferrules, but now Instrumentation engineers/technicians prints out desired ferrules by using a ferrule printing machine. Typical Ferrule The numbers/ letters on the ferrules will be given as per the approved electrical hook up or loop diagrams. This helps technicians to easily identify a particular loop/wiring from a series of terminal blocks and to troubleshoot the desired terminal connection. Separate numbers on the ferrules distinguish the positive and negative polarities of wires, thus ensure the polarity protection of the instrument. Cross Ferruling As a wire is connected on its both ends, it is quite useful to use a cross reference method for wire identification. Unlike normal ferru...

What is a Torbar? – Averaging Pitot Tubes

The Torbar is employed for flow measurement of liquids, gases, or steam in circular, square, or rectangular section ducts for large flow rates. The Torbar is an insertion type multi-port self-averaging primary sensor for flow measurement. Torbar TORBAR is a set of Pitot tubes mounted on a bar across the pipeline with no moving parts. An averaging Pitot tube is a technology, while TORBAR is a manufacturing brand name. There are several brands available in the market with VERABAR, ANNUBAR, etc. Averaging Pitot Tube Principle Purpose Averaging Pitot tube can be employed when the average velocity of the flow profile, rather than the velocity in a specific point in the cross-section is desired. Averaging Pitot Tubes Principle It measures the differential pressure between the static pressure tap and the tap of full pressure of a stream. Thus such magnitude of differential pressure is directly proportional to the square of the flow rate. Working The TORBAR is designed in such a way that ...

Dissolved Oxygen Analyzer Working Principle

What is dissolved oxygen ? Dissolved oxygen refers to oxygen dissolved in water. Its concentration is expressed as the amount of oxygen per unit volume and the unit is mg/L. Biologically, oxygen is an essential element for respiration of underwater life and also acts as a chemical oxidizer. The solubility of oxygen in water is affected by water temperature, salinity, barometric pressure, etc. and decreases as water temperature rises. Measurement of dissolved oxygen by the membrane electrode method The membrane electrode method measures a diffusion current or reduction current generated by the concentration of dissolved oxygen or partial pressure of oxygen to obtain the concentration of dissolved oxygen. This method is not affected by the pH value of water being measured, oxidation and reduction substances, color, turbidity, etc. and the measurement method offers good reproducibility. When a sensor is inserted into water, an air layer forms on the membrane (Teflon membrane). The ox...

TILI Automation

Search This Blog