Skip to main content

What is a Electric Solenoid Actuator ?

 A typical electric solenoid actuator is shown in Below Figure. It consists of a coil, armature, spring, and stem.

Note : Electric Solenoid Actuator also called as ON/OFF valve or Solenoid Valve.

Electric Solenoid Actuator


The coil is connected to an external current supply. The spring rests on the armature to force it downward. The armature moves vertically inside the coil and transmits its motion through the stem to the valve.

When current flows through the coil, a magnetic field forms around the coil. The magnetic field attracts the armature toward the center of the coil. As the armature moves upward, the spring collapses and the valve opens. When the circuit is opened and current stops flowing to the coil, the magnetic field collapses. This allows the spring to expand and shut the valve.


A major advantage of solenoid actuators is their quick operation. Also, they are much easier to install than pneumatic or hydraulic actuators. However, solenoid actuators have two disadvantages. First, they have only two positions: fully open and fully closed. Second, they don’t produce much force, so they usually only operate relatively small valves.

Labels:

Comments

  1. adextermagDecember 10, 2020 at 8:45 PM

    I think this is one of the most important pieces of information for me. And I’m glad to read your article. Thank you for sharing. Magnetic Actuator

    ReplyDelete

Post a Comment

Popular posts from this blog

Ferrules and Cross Ferruling

 Ferrules are identification labels provided for every wire terminations in an instrument, equipment, or electrical/instrumentation control panels. These tube-shaped sleeves can be inserted easily on each individual wire in a multi-core cable. In earlier days fixed digits/letters are used as ferrules, but now Instrumentation engineers/technicians prints out desired ferrules by using a ferrule printing machine. Typical Ferrule The numbers/ letters on the ferrules will be given as per the approved electrical hook up or loop diagrams. This helps technicians to easily identify a particular loop/wiring from a series of terminal blocks and to troubleshoot the desired terminal connection. Separate numbers on the ferrules distinguish the positive and negative polarities of wires, thus ensure the polarity protection of the instrument. Cross Ferruling  As a wire is connected on its both ends, it is quite useful to use a cross reference method for wire identification. Unlike normal ferru...
2 comments
Read more

What it is MQTT?

 MQTT is an acronym for Message Queuing Telemetry Transport. It is a lightweight, publish-subscribe, machine to machine network protocol for message queue / message queuing service1. It is designed for connections with remote locations that have devices with resource constraints or limited network bandwidth, such as in the Internet of Things (IoT) . MQTT was created by Andy Stanford-Clark (IBM) and Arlen Nipper (then working for Eurotech, Inc.) in 1999. It was used to monitor oil pipelines within the SCADA industrial control system 1. The goal was to have a protocol that is bandwidth-efficient, lightweight and uses little battery power, because the devices were connected via satellite link which, at that time, was extremely expensive. MQTT is based on a client-server architecture, where a message broker acts as a server that receives all messages from the clients and then routes the messages to the appropriate destination clients . MQTT uses a publish-subscribe model, where clients...
4 comments
Read more

What is a Torbar? – Averaging Pitot Tubes

 The Torbar is employed for flow measurement of liquids, gases, or steam in circular, square, or rectangular section ducts for large flow rates. The Torbar is an insertion type multi-port self-averaging primary sensor for flow measurement. Torbar TORBAR is a set of Pitot tubes mounted on a bar across the pipeline with no moving parts. An averaging Pitot tube is a technology, while TORBAR is a manufacturing brand name. There are several brands available in the market with VERABAR, ANNUBAR, etc. Averaging Pitot Tube Principle Purpose Averaging Pitot tube can be employed when the average velocity of the flow profile, rather than the velocity in a specific point in the cross-section is desired. Averaging Pitot Tubes Principle It measures the differential pressure between the static pressure tap and the tap of full pressure of a stream. Thus such magnitude of differential pressure is directly proportional to the square of the flow rate. Working The TORBAR is designed in such a way that ...
7 comments
Read more